Changelog
Rendered from the same table the documentation uses, so a release cannot appear in one place and not the other.
1.4.8
2026-09-23Supported- Disconnecting your iPad now keeps it disconnected. The app used to reconnect it ten seconds later because it could not tell your disconnect from a dropped connection. Reconnecting is now off by default; turn on "Reconnect my iPad display if it drops" in the menu if you want it
1.4.7
2026-09-23Supported- Disconnecting an iPad used as a display no longer leaves a supersampled monitor on the wrong side of the laptop. macOS sometimes switches that monitor's supersampling off as the iPad leaves; the app now switches it back on the same display event instead of 1.5 seconds later
1.4.6
2026-09-23Supported- An iPad used as a display comes back at the resolution you pinned after it reconnects. Before, it often stayed at its native size, with smaller text, because the app looked for the pinned mode before the iPad had finished listing its modes and never looked again
1.4.5
2026-09-23Supported- The app never moves a window. Opening or quitting it only changes the monitors; it no longer picks up, carries or hands over any app's windows between screens or desktops
1.4.4
2026-09-23Supported- A monitor is only switched to supersampling once its new desktop is ready to take its windows. On a busy Mac the switch could come first, and the windows then went to the built-in screen
- Quitting with two supersampled monitors no longer drops a window on the built-in screen: each monitor's windows are confirmed on it before the app exits
1.4.3
2026-09-23Supported- Opening or quitting the app no longer rearranges your windows or desktops. Before a monitor is switched to supersampling, and before it is switched back, every window on it moves to the matching desktop of the screen taking its place, at the same position — so macOS has nothing to shuffle, and the app no longer chases windows around for two minutes afterwards
- Fixed a crash when two connected displays report the same identity; the crash switched every monitor back to normal and scattered its windows
1.4.2
2026-09-21Supported- Windows stay where you put them. When the app rebuilds a supersampled monitor it no longer picks up windows that live on a different screen's desktop — an iPad window was being dragged onto a Dell and resized to 1728x1049 on a 1016x810 screen
- A window macOS pulls back off a monitor while the desk is still settling is now put back. Before, the app tried once, logged success, and never looked again
- A window move is reported from where the window actually is, not from whether the command returned. A timed-out move that had in fact applied was being logged as refused and counted as a success at the same time
1.4.1
2026-09-21Supported- Fixes 1.4.0: an iPad you use as a display is now remembered between launches, so plugging the cable back in brings it up even if the app was restarted while the iPad was off. In 1.4.0 it only recovered a display the running app had already watched connect, which is not the case anyone actually hits
- The app no longer stops trying after three attempts — it keeps checking every five minutes, so an iPad that becomes reachable an hour later still comes back
1.4.0
2026-09-21Supported- An iPad used as a second display comes back by itself. When macOS drops a Sidecar session it retries three times in sixteen seconds and then gives up silently — this keeps trying, and picks the display up again the moment the cable goes back in. Turn it off in the menu, or with `dsp sidecar off`
- `dsp sidecar` shows which iPads macOS can see and which are connected, and can connect one from a terminal
- The log names the screen that arrived or left, the second it happens, instead of leaving you to spot a changed number in a health line
- The desktop on your built-in display is never switched by the app — only the ones it created itself
- A window that macOS moves off an external monitor at launch comes back once that screen is steady, rather than after the whole desk settles
1.3.3
2026-09-21Supported- Quitting hands each external monitor back its own resolution in the same instant it stops mirroring. No in-between resolution any more (was up to five seconds)
- When the app opens, windows that macOS moves off an external monitor come back the moment they move, not after a fixed wait
1.3.2
2026-09-21Supported- Quitting Display Upscale puts each external monitor back on its own resolution. Before, macOS left it on the timing of the virtual display that had just gone away
- Reinstalling never leaves the Mac without an agent: the installer waits for the old one to finish, and a replacement waits ten seconds for its turn instead of giving up
1.3.1
2026-09-21Supported- Opening Display Upscale no longer moves the windows on your external monitors onto the built-in display. Every window stays on the screen it was on
- Your display arrangement is read once, before any virtual display is created, so a screen is never seated at a position macOS only passed through while the app was starting
- Where macOS does move a window off a panel, the app puts it back — using Accessibility if you have granted it, or yabai if it is installed. It never asks for either
1.3.0
2026-09-21Supported- Your macOS display arrangement is honoured, whether Display Upscale is running or not. Drag your screens in System Settings and it sticks — while the app is open, and after reopening it
- macOS keeps a separate arrangement for each set of displays connected. The app now follows the one you are actually using instead of re-imposing its own record
- "Lock display arrangement" now means what people expected: your desk comes back after a replug, a wake or a login, and stays changeable the rest of the time
- Fixed: rearranging displays while the app was open was undone within half a second, and an arrangement set with the app closed was thrown away the next time it opened
1.2.0
2026-09-02Security fixes only- `dsp super` — supersample a 1080p external panel through a virtual display: the desktop stays the same size, rendered at 2x and resampled down. Every route is in the menu, and the panel keeps its own colour primaries and profile
- Curated colour profiles per display, assigned reversibly from the menu
- Backup, revert and undo of every display setting, and a locked arrangement nothing can write over
- Brightness, contrast and sharpness sliders in the menu, per monitor; the menu-bar mark is coloured and animates on change
- `dsp doctor` finds an HDCP link stuck renegotiating — the cause of coloured squares on a panel — and the agent snapshots its health and memory pressure to ~/Library/Logs/dsp.log
- Fixed: ColorSync spinning a core on ghost display identities (pruned at every agent start); a 75Hz panel landing on 800x600 when supersampled; two menu-bar agents after a reinstall
1.1.0
2026-08-04End of life- `dsp doctor` — one command that finds everything wrong with your displays, ranked, with the fix for each. Free on every tier.
- Desk profiles: name the set of displays in front of you and every mode, brightness and contrast returns automatically when they reappear (Pro)
- `dsp ddc all` sets every external display at once, and values accept +N / -N steps
- Fixed: a DDC write did not wait the mandated 50ms before the next command, so the command after any write was silently dropped by the panel
1.0.0
2026-08-04End of life- Menu-bar agent that keeps every managed display on its sharpest 1:1 mode
- Pinned per-display profiles that survive sleep, replug and reboot
- Monitor controls over DDC/CI — brightness, contrast, sharpness, colour
- EDID override generation, refused for panels macOS already drives fully
- Offline licence verification; Free, Pro and Studio tiers
Full commit history and release artefacts: github.com/deepakmarathe/display-upscale